MOSFET, N-CH, 650V, 75A, 150DEG C, 446W; Transistor Polarity:N Channel; Drain Source Voltage Vds:650V; Continuous Drain Current Id:75A; On Resistance Rds(on):0.017ohm; Transistor Mounting:Through Hole; Rds(on) Test Voltage Vgs:10V RoHS Compliant: Yes

MOSFET DRIVER, LOW-SIDE, DIP-8; Driver Configuration:Low Side; Peak Output Current:3.3A; Supply Voltage Min:12V; Supply Voltage Max:18V; Driver Case Style:DIP; No. of Pins:8Pins; Input Delay:150ns; Output Delay:200ns; Product Range:-RoHS Compliant: Yes

N-Channel 55V 110A (Tc) 200W (Tc) Surface Mount D2PAK

N-Channel 100V 9.7A (Tc) 48W (Tc) Through Hole TO-220AB

N-Channel 100V 9.7A (Tc) 3.8W (Ta), 48W (Tc) Through Hole TO-262

N-Channel 100V 9.7A (Tc) 3.8W (Ta), 48W (Tc) Surface Mount D2PAK

Mouser Electronics

Digi-Key Electronics

Element14

Farnell

NAC Semi

Newark

Verical

Arrow Americas

The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small form factor, wide RF bandwidth, highly linear, low insertion loss switch that is operational from 0 Hz/dc to 14 GHz, making the ADGM1304 an ideal solution for a wide range of RF and precision equipment switching needs.
An integrated driver chip generates a high voltage to electrostatically actuate a switch that can be controlled by a parallel interface and a serial peripheral interface (SPI). All four switches are independently controllable.
The device is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm, lead frame chip-scale package (LFCSP).
To ensure optimum operation of the ADGM1304, the Critical Operational Requirements section must be followed exactly.
The on resistance (RON) performance of the ADGM1304 is affected by device to device variation, channel to channel variation, cycle actuations, settling time post turn on, bias voltage, and temperature changes.
Applications

    Relay replacements
    Automatic test equipment: RF/high speed digital and mixed signals
    Load and probe boards: RF/high speed digital and mixed signals
    RF test instrumentation
    Reconfigurable filters and attenuators
    High performance RF switching

The ADM6326/ADM6328/ADM6346/ADM6348 devices provide low cost solutions for protecting sensitive circuitry, such as micro-processor and telecommunications circuitry.
With built-in glitch immunity, ultralow supply currents, and 24 reset threshold voltage options, the ADM6326/ADM6328/ADM6346/ADM6348 not only ensure that systems are immune to fast transients on VCC, but also that the devices are suitable for monitoring a variety of supply voltages in low power, portable equipment.
These devices provide a reset output during power-up, power-down, and brownout conditions. On power-up, an internal timer holds RESET asserted for at least 100 ms. This holds the microprocessor in a reset state until conditions have stabilized. The reset output remains operational with VCC as low as 1 V.
The ADM6326 and ADM6346 have an active low push-pull reset output. The ADM6328 and ADM6348 have an active low open-drain reset output, which requires an external pull-up resistor. The ADM6326 and ADM6328 offer a choice of ten reset thresholds in increments between 2.2 V and 3.08 V, whereas the ADM6346 and ADM6348 offer a choice of 14 reset thresholds between 3.3 V and 4.63 V. Not all options are released for sale as standard models. See the Ordering Guide for details.
These devices are available in a 3-lead SOT-23 package and operate over the extended temperature range of −40°C to +85°C.
Applications

    Telecommunications
    Microprocessor systems
    Desktop and notebook computers
    Portable equipment

The ADuCM322 is a fully integrated, single package device that incorporates high performance analog peripherals together with digital peripherals controlled by an 80 MHz ARM® Cortex™-M3 processor and integral flash for code and data.
The ADC on the ADuCM322 provides 12-bit, 1 MSPS data acquisition on up to 16 input balls. Additionally, chip temperature and supply voltages can be measured.
The ADC input voltage range is 0 V to VREF. A sequencer is provided, which allows a user to select a set of ADC channels to measure in sequence without software involvement during the sequence. The sequence can optionally repeat automatically at a user selectable rate. Up to eight VDACs are provided with output ranges that are programmable to one of two voltage ranges.
The ADuCM322 can be configured so that the digital and analog outputs retain their output voltages through a watchdog or software reset sequence. Thus, a product can remain functional even while the ADuCM322 is resetting itself.
The ADuCM322 has a low power ARM Cortex-M3 processor and a 32-bit RISC machine that offers up to 100 MIPS peak perfor-mance. Also integrated on-chip are 2 × 128 kB Flash/EE memory blocks and 32 kB of SRAM. The flash comprises two separate 128 kB blocks supporting execution from one flash block and simultaneous writing/erasing of the other flash block.
The ADuCM322 operates from an on-chip oscillator or a 16 MHz external crystal and a PLL at 80 MHz. This clock can optionally be divided down to reduce current consumption. Additional low power modes can be set via software. In normal operating mode, the ADuCM322 digital core consumes about 300 μA per MHz.
The device includes an MDIO interface capable of operating at up to 4 MHz. The capability to simultaneously execute from one flash block and write/erase the other flash block makes the ADuCM322 ideal for 10G, 40G, and 100G optical applications. In addition, the nonerasable kernel code plus flags in user flash provide assistance by allowing user code to robustly switch between the two blocks of user flash code and data spaces.
The ADuCM322 integrates a range of on-chip peripherals that can be configured under software control, as required in the application. These peripherals include 1 × UART, 2 × I2C, and 2 × SPI serial input/output communication controllers, GPIO, 32-element PLA, three general-purpose timers, plus a wake-up timer and system watchdog timer. A 16-bit PWM with seven output channels is also provided.
GPIO balls on the device power up in high impedance input mode. In output mode, the software chooses between open-drain mode and push-pull mode. The pull-up resistors can be disabled and enabled in software. In GPIO output mode, the inputs can remain enabled to monitor the balls. The GPIO balls can also be programmed to handle digital or analog peripheral signals; in such cases, the ball characteristics are matched to the specific requirement.
A large support ecosystem is available for the ARM Cortex-M3 processor to ease product development of the ADuCM322. Access is via the ARM serial wire debug port (SW-DP). On-chip factory firmware supports in-circuit serial download via MDIO. These features are incorporated into a QuickStart™ development system, supporting this precision analog microcontroller family.
Applications

    Optical networking

The ADuCM360 is a fully integrated, 3.9 kSPS, 24-bit data acquisition system that incorporates dual high performance, multichannel sigma-delta (Σ-Δ) analog-to-digital converters (ADCs), a 32-bit ARM Cortex™-M3 processor, and Flash/EE memory on a single chip. The ADuCM360 is designed for direct interfacing to external precision sensors in both wired and battery-powered applications. The ADuCM361 contains all the features of the ADuCM360 except that only one 24-bit Σ-Δ ADC (ADC1) is available.

The ADuCM360/ADuCM361 contain an on-chip 32 kHz oscillator and an internal 16 MHz high frequency oscillator. The high frequency oscillator is routed through a programmable clock divider from which the operating frequency of the processor core clock is generated. The maximum core clock speed is 16 MHz; this speed is not limited by operating voltage or temperature.

The microcontroller core is a low power ARM Cortex-M3 processor, a 32-bit RISC machine that offers up to 20 MIPS peak performance. The Cortex-M3 processor incorporates a flexible, 11-channel DMA controller that supports all wired communica-tion peripherals (SPI, UART, and I2C). Also integrated on chip are 128 kB of nonvolatile Flash/EE memory and 8 kB of SRAM.

The analog subsystem consists of dual ADCs, each connected to a flexible input mux. Both ADCs can operate in fully differential and single-ended modes. Other on-chip ADC features include dual programmable excitation current sources, diagnostic current sources, and a bias voltage generator of AVDD_REG/2 (900 mV) to set the common-mode voltage of an input channel. A low-side internal ground switch is provided to allow power-down of an external circuit (for example, a bridge circuit) between conversions.

The ADCs contain two parallel filters: a sinc3 or sinc4 filter in parallel with a sinc2 filter. The sinc3 or sinc4 filter is used for precision measurements. The sinc2 filter is used for fast measure-ments and for the detection of step changes in the input signal.

The devices contain a low noise, low drift internal band gap ref-erence, but they can be configured to accept one or two external reference sources in ratiometric measurement configurations. An option to buffer the external reference inputs is provided on chip. A single-channel buffered voltage output DAC is also provided on chip.

The ADuCM360/ADuCM361 integrate a range of on-chip peripherals, which can be configured under microcontroller software control as required in the application. The peripherals include UART, I2C, and dual SPI serial I/O communication controllers; a 19-pin GPIO port; two general-purpose timers; a wake-up timer; and a system watchdog timer. A 16-bit PWM controller with six output channels is also provided.

The ADuCM360/ADuCM361 are specifically designed to operate in battery-powered applications where low power operation is critical. The microcontroller core can be configured in a normal operating mode that consumes 290 μA/MHz (including flash/ SRAM IDD). An overall system current consumption of 1 mA can be achieved with both ADCs on (input buffers off), PGA gain of 4, one SPI port on, and all timers on.

The ADuCM360/ADuCM361 can be configured in a number of low power operating modes under direct program control, including a hibernate mode (internal wake-up timer active) that consumes only 4 μA. In hibernate mode, peripherals such as external interrupts or the internal wake-up timer can wake up the device. This mode allows the part to operate with ultralow power and still respond to asynchronous external or periodic events.

Applications

    Industrial automation and process control
    Intelligent precision sensing systems
    4 mA to 20 mA loop-powered smart sensor systems
    Medical devices, patient monitoring

The HMC329 devices are double-balanced MMIC mixers that are available in a chip (HMC329), a leadless RoHS compliant SMT package (HMC329LC3B), and an SMT leadless chip carrier package (HMC329LM3). The HMC329 devices can be used as an upconverter or downconverter. On the HMC329, the mixer is used as an upconverter or downcnverter in a small chip area of 0.85 mm × 0.55 mm. Excellent isolations are provided by on-chip baluns, and the chip requires no external components and no dc bias. Measurements for the HMC329 were made with the chip mounted and ribbon bonded into in a 50 Ω microstrip test fixture that contains 5 mil alumina substrates between the chip and K connectors. Measured data includes the parasitic effects of the assembly. RF connections to the chip were made with 0.076 mm (3 mil) ribbon bond with minimal length less than 0.31 mm (<12 mil).
Applications


    Microwave point-to-point radios 
    Point-to-point radios 
    Point-to-multipoint radios and very small aperture terminal (VSAT)
    Local multipoint distribution systems (LMDS)
    Satellite communications (SATCOM)
    Test equipment and sensors 
    Military end use
    RADAR

The HMC787A is a general-purpose, double balanced mixer in a 12-terminal, RoHS compliant, ceramic leadless chip carrier (LCC) package that can be used as an upconverter or down- converter from 3 GHz to 10 GHz. This mixer is fabricated in a gallium arsenide (GaAs), metal semiconductor field effect transistor (MESFET) process and requires no external components or matching circuitry. The HMC787A provides excellent local oscillator (LO) to radio frequency (RF) and LO to intermediate frequency (IF) isolation due to optimized balun structures and operates with a LO drive level of 17 dBm. The ceramic LCC package eliminates the need for wire bonding and is compatible with high volume, surface-mount manufacturing techniques.
Applications

    Microwave Radio
    Industrial, scientific, and medical (ISM) band and ultrawide band (UWB) radio
    Test equipment & sensors
    Military end use

TERMINAL, WIRE FERRULE, 4AWG, BROWN; Wire Ferrule Type:Single Wire; Wire Size AWG Max:4AWG; Conductor Area CSA:25mm²; Pin Length:16mm; Insulator Colour:Brown; Product Range:E Series; Overall Length:28mm; Terminal Material:Copper RoHS Compliant: Yes

Special Order: 22759/32-12-1 Cable Type: MIL-DTL-22759 Voltage Rating: 600 V Wire Color: Brown Insulation Material: Modified Radiation Cross-linked ETFE Polymer Conductor Material: Tin-Coated Copper MIL-DTL-22759 600 V Brown Modified Radiation Cross-linked ETFE Polymer | Hook Up Wire | Part Number: 22759/32-12-1 | Internal Number: 295567-000 | Alias Number: 3-1192239-4 | TE Connectivity

Rotary Potentiometer, Spindle Operated, 23EXA Series, 10 kohm, Linear, 1, 400 mW, Through Hole RoHS Compliant: Yes

Z8F3222AR020EC

ZiLOG, Inc.

Suppliers

Supplier

SKU

Stock

Price Range

Digi-Key Electronics

269-3279-ND

0

Mouser Electronics

692-Z8F3222AR020EC

Out Of Stock

320

$4.76

640

$4.27

1120

$3.60

2560

$3.42

5120

$3.24

10080

$3.13

Copyright © 2021 WTWH Media LLC and its licensors. All rights reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.

Privacy Policy

Z8F3222AR020EC

ZiLOG, Inc.

Suppliers

Supplier

SKU

Stock

Price Range

Digi-Key Electronics

269-3279-ND

0

Mouser Electronics

692-Z8F3222AR020EC

Out Of Stock

320

$4.76

640

$4.27

1120

$3.60

2560

$3.42

5120

$3.24

10080

$3.13

Copyright © 2021 WTWH Media LLC and its licensors. All rights reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.Privacy Policy

Copyright © 2021 WTWH Media LLC and its licensors. All rights reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.

Privacy Policy